Modelling of Remediation of Polluted Soil by In-Situ Electokinetic Treatment |
 |
Sadataka Shiba, Yushi Hirata |
2 |
Estimation of the Long-Term Strength of Grouted Sand |
|
Munehiko Kaga |
6 |
Influence of Allophene Content on the Environmental Geotechnical Properties for Kanto Loam |
|
Ei-kon So, Kazuto Endo, Shigeyuki Asano |
10 |
The Application of Surplus Soils to Embankment by the Mechanical Stabilization |
|
Kazuo Sasaba, Atusi Koto, Kazuyuki Suzuki, Yosinobu Katayama, Isao Takeuchi |
14 |
Geotechnical Properties of Crushed Cement-Stabilized Sludge and its Trial Application to Vertical Drain |
|
Yasuyuki Nabeshima, Tamotsu Matsui, Hiromi Hamano |
18 |
Performance of Cement-Bentonite Slurru Wall against Heavy Metals Containment |
|
Masashi Kamon, Takeshi Katsumi, Kazuto Miyatake |
22 |
Eluted Oil Properties of Treated Soil by the Dustless Hardening Material |
|
Kohei Sawa, Seishi Tomohisa, Yuka Teraoka |
26 |
Effect of Bamboo Grass for Stability of a Slope Surface |
|
Tetsuji Yamada, Kazuo Takada, Akihiko Okamura, Takahiro Itoh |
30 |
The Fundamental Tests on Application of MSW Direct Melting Slag as Soil Improvement Material |
|
Morihiro Osada, Nobuyoshi Nishihara, Shouichi Osada, Hitoshi Miura, Yukio Morita, Asao Suwa |
34 |
The Fundamental Study on Soil Prevention Method of Liquefaction Using Electrophoresis of Fixative Materials |
|
Masami Fujihira, Eiji Shimizu, Takeshi Konishi, Susumu Yasuda, Tetuji Shimizu |
38 |
Evaluation of Liquefaction Potential Using Cone Penetration Tests Results after Soil Improvement for Silty Sand |
|
Michiharu Ikeda, Yasunori Sasaki, Tsan Lin Yu |
42 |
Recycle of Construction Sludge in Soil-Cement Diaphragm Walls |
|
Takeo Suzuki, Toshimitsu Kunito, Motohiro Nishi |
46 |
Microstructure and Mechanical Properties of Thermal Sprayed Aluminum Coatings |
|
Yoshiyasu Itoh, Hideyasu Andoh, Shoko Suyama |
51 |
Residual Stress Characteristics of Thermal Sprayed Aluminum Coatings |
|
Yoshiyasu Itoh, Hideyasu Andoh, Shoko Suyama |
56 |
Fatigue Properties of Shot-Peened Notched Components in Ti-6Al-4V Alloy at Elevated Temperatures |
|
Shinzaburo Takafuji, Yozo Kato, Keiro Tokaji |
61 |
Effect of Residual Stress on Matrix Cracking in Continuous Fiber-Reinforced SiC Matrix Composites |
|
Yoshiyasu Itoh, Shoko Suyama, Tsuneji Kameda, Katsutoshi Nishida |
66 |
An Experimental Study on Dynamic Ultimate Limit States of Prestressed Concrete and Prestressed Reinforced Concrete Beams under High Speed Loading |
|
Nobutaka Ishikawa, Hidenobu Enrin, Satoshi Katsuki, Toshiaki Ohta |
72 |
Creep Crack Growth Test Method and Creep Crack Growth Properties for TiAl Intermetallic Compound |
|
Masaaki Tabuchi, Toshimitu Yokobori, Akio Fuji, Kiyoshi Kubo, Koichi Yagi, Takeo Yokobori |
80 |
Effect of the Chemical Compositon on the Mechanical Properties and Stress Corrosion Cracking Sensitivities of High-Strength Al-Zn-Mg Alloy |
|
Masakazu Hirano, Kazunori Kobayasi, Hideki Tonda |
86 |
Effect of the Additional Element on the Weldability of High-Strength Al-Zn-Mg Alloy |
|
Masakazu Hirano, Kazunori Kobayasi, Hideki Tonda |
92 |
Study of Stress Functions for Half-Infinite Anisotropic Plate with Crack Pararllel to the Free Edge |
|
Kouju Fujii, Hironobu Nagase, Ryouta Doi, Kenji Nakagawa, Yasuhide Abe, Yasuhiko Murase |
98 |
Study of Improvement of Accuracies due to Hole Drilling Method for Measurement of Residual Stresses |
|
Yuichi Kawagishi, Yoshihide Chino, Ken-ichi Hirashima, Hajime Hirose |
106 |
Injection Molding and Material Property of Biodegradable Composite Using Waste of Cotton Fiber as Reinforcement |
|
Teruo Kimura, Yoshiaki Kataoka, Yukie Kondo, Tetsuya Takahashi |
111 |
X-Ray Study on Mechanical Behavior of Thermal Barrier Coated Film |
|
Kenji Suzuki, Shutaro Machiya, Keisuke Tanaka, Yoshihisa Sakaida |
117 |
