Contents56-6

Vol. 56 No. 6 CONTENTS
Special Issue on Ceramic　Materials
General Paper

Special Issue on Ceramic　Materials (Vol.56 No.6)

Review paper (Vol.56 No.6)

Fracture-Induced Permanent Deformation and Structural Change in Glass

Jun Matsuoka
489

Technical Topics (Vol.56 No.6)

Fabrication of Advanced Glasses by a Staining Process

Kohei Kadono
495

Original Paper (Vol.56 No.6)

Microstructure of Nano-Porous NaNbO₃Particles Synthesized by Sol-Crystal Method

Hiromi NAKANO, Yosuke HIRANO, and Yoko SUYAMA
500

High-Temperature Deformation of Si₃N₄/Si₃N₄-SiC Hybrid Composites with Belt-Like Network Structure of Si₃N₄-SiC Composites

K.Yamada, N.Kamiya, N.Kondo and H.Wakai
505

Development of Instrumented Indentation Microscope and Its Application to Indentation Contact Mechanics

Norio HAKIRI, Mototsugu SAKAI, and Tatsuya MIYAJIMA
510

Effect of Addition to the Gypsum on Phosphorous Removal Properties of　Wollastonite-Type Adsorbent

Ryouta FUKUI, Tomohiko KURAHASHI, Haruhisa SHIOMI, Satoko KITAGUTI and Mio SHIRAKAWA
516

Ultrasonic Vibration Potental of Cerium Dioxide-Alumina Composite Particles in Water

Masatomo HATTORI, Takashi ISHIDA and Masakuni OZAWA
521

Sintering of Al₂O₃-Cr₂O₃ Powder Prepared by Sol-Gel Process

Motonari FUJITA, Keisuke INUKAI, Shinichi SAKIDA, Tokuro NANBA, Junji OMMYOJI, Akira YAMAGUCHI and Yoshinari MIURA
526

General Paper (Vol.56 No.6)

Original Paper (Vol.56 No.6)

Mechanical and Electrical Properties and Microstructure in Cu-Ni-Be Alloys

Satoshi OTA，Naokuni MURAMATSU，Kazumasa SENGOKU，Chihiro WATANABE and Ryoichi MONZEN
531

Fatigue Behaviour of Friction Stir Spot Welded Al-Mg-Si Alloy

Yoshihiko UEMATSU, Keiro TOKAJI, Shunsuke MURATA, Yasunari TOZAKI and Tatsuo KURITA
537

Reliability Based Defect Assessment Methodology for Welded Joints with Respected to Brittle Fracture

Norio YAMAMOTO, Ryosuke MURAI and Hitoshi YOSHINARI
544

Mechanical Properties of Aluminum Coatings Produced by Cold Spraying

Yoshiyasu ITOH, Shoko SUYAMA and Toshiaki Fuse
550

Lecture (Vol.56 No.6)

The Frontier of Risk-Based Engineering Ⅱ:Relaibility Engineering and Risk-Based Engineering

Shinsuke SAKAI
556

Fracture-Induced Permanent Deformation and Structural Change in Glass
Jun Matsuoka	489

Fabrication of Advanced Glasses by a Staining Process
Kohei Kadono	495

Microstructure of Nano-Porous NaNbO₃Particles Synthesized by Sol-Crystal Method
Hiromi NAKANO, Yosuke HIRANO, and Yoko SUYAMA	500
High-Temperature Deformation of Si₃N₄/Si₃N₄-SiC Hybrid Composites with Belt-Like Network Structure of Si₃N₄-SiC Composites
K.Yamada, N.Kamiya, N.Kondo and H.Wakai	505
Development of Instrumented Indentation Microscope and Its Application to Indentation Contact Mechanics
Norio HAKIRI, Mototsugu SAKAI, and Tatsuya MIYAJIMA	510
Effect of Addition to the Gypsum on Phosphorous Removal Properties of　Wollastonite-Type Adsorbent
Ryouta FUKUI, Tomohiko KURAHASHI, Haruhisa SHIOMI, Satoko KITAGUTI and Mio SHIRAKAWA	516
Ultrasonic Vibration Potental of Cerium Dioxide-Alumina Composite Particles in Water
Masatomo HATTORI, Takashi ISHIDA and Masakuni OZAWA	521
Sintering of Al₂O₃-Cr₂O₃ Powder Prepared by Sol-Gel Process
Motonari FUJITA, Keisuke INUKAI, Shinichi SAKIDA, Tokuro NANBA, Junji OMMYOJI, Akira YAMAGUCHI and Yoshinari MIURA	526

Mechanical and Electrical Properties and Microstructure in Cu-Ni-Be Alloys
Satoshi OTA，Naokuni MURAMATSU，Kazumasa SENGOKU，Chihiro WATANABE and Ryoichi MONZEN	531
Fatigue Behaviour of Friction Stir Spot Welded Al-Mg-Si Alloy
Yoshihiko UEMATSU, Keiro TOKAJI, Shunsuke MURATA, Yasunari TOZAKI and Tatsuo KURITA	537
Reliability Based Defect Assessment Methodology for Welded Joints with Respected to Brittle Fracture
Norio YAMAMOTO, Ryosuke MURAI and Hitoshi YOSHINARI	544
Mechanical Properties of Aluminum Coatings Produced by Cold Spraying
Yoshiyasu ITOH, Shoko SUYAMA and Toshiaki Fuse	550

The Frontier of Risk-Based Engineering Ⅱ:Relaibility Engineering and Risk-Based Engineering
Shinsuke SAKAI	556