Vol. 50 No. 5 CONTENTS
Special Issue on
Composite Material
General Paper

Special Issue on Composite Material (Vol.50 No.5)

Original Paper (Vol.50 No.5)

Laminated Structure and Its Mechanical Properties of the Fore-Wing of Beetle

Jinxiang CHEN, Masaharu IWAMOTO, Qing-Qing NI, Ken KURASHIKI and Kenji SAITO

455

Deep-Drawing Simulation of Knitted Fabric Reinforced Thermoplastics by Homogenization Theory and Experimental Verification

Naoki TAKANO, Yoshihiro OHNISHI, Kazuaki NISHIYABU and Masaru ZAKO

461

Formability in SMC Roll Forming-Influence of Reduction, Roll Velocity and Roll Diameter on Load and Deformation Characteristics in Forming Process-

Tsutao KATAYAMA, Kazumasa KUROKAWA, Atsushi KITADE, Go KAMADA, Masahiro SHINOHARA and Masahiro HAKOTANI

468

Evaluation of Mechanical Properties of Hollow Particle Reinforced Composites and Analyses Aimed at Their Improvement

Hiroyuki TODA, Hisashi KAGAJO, Kazuo HOSOI, Toshiro KOBAYASHI, Yosuke ITO, Takashi HIGASHIHARA and Takashi GOHDA

474

Mixed Mode(‡T+‡U)Fracture Toughness and Rate Dependent Fracture Behavior of Interlayer-Toughened Composite Laminate

Noriyo HORIKAWA, Takayuki KUSAKA and Masayoshi MASUDA

482

Three-Dimensional Evaluation of Permeability of Fiber Reinforced Composite Materials Based on Their Microstructures

Naoki TAKANO, Kenjiro TERADA and Masaru ZAKO

488

Electric Resistance Change Method for Identification of Embedded Delamination of CFRP Plates

Akira TODOROKI, Yuuki TANAKA and Yoshinobu SHIMAMURA

495


General Paper (Vol.50 No.5)

Original Paper (Vol.50 No.5)

Creep Damage Evaluation of W Alloyed 9%Cr Ferritic Steel by Electrochemical Method

Shin-ichi KOMAZAKI, Shigeo KISHI, Tetsuo SHOJI, Kojiro HIGUCHI and Koshi SUZUKI

503

Evaluation of Crack Initiation and Propagation Lives from Internal Defects and Lower Limit of Failure Life in High Temperature Fatigue on Ni-Based Single Crystal Superalloy

Masato YAMAMOTO, Akito NITTA and Takashi OGATA

510

Fatigue Life Prediction for Bearing Steel Failed with Fish-Eye at Subsurface in Rotating Bending

Noriyasu OGUMA and Tatsuo SAKAI

516

A Simple Method for Predicting the Singular Stress Distribution of Mode I Interlamellar Crack Embedded in Unidirectionally-Fiber-Reinforced Composites

Naoya TADA, Ryuichi OHTANI and Hiroyuki SAKURAI

524

Delamination Energy Evaluation of 8mass% Y2O3-ZrO2 Coating Sprayed on Co-Based Superalloy

Masahiko KATO, Keijiro NAKASA, Lin GAO, Teruhito BANSHO, Hidetaka NISHIDA and Hiroshi YAMAGUCHI

532

Corrosion Resistance of Aluminum Nitride Ceramics Modified by Pre-Oxidation and Sputtering Metallization in Water at 100Ž

Hiroyasu TAMAI, Takashi HAMAUZU, Akihito RYUMON, Hitohumi TANIGUCHI, Kaoru AOKI, Kohei ODA and Tetsuo YOSHIO

538

Strength Development and Autogenous Shrinkage of High-Flow Concrete with Limestone Powder

Hiroyoshi KATO, Akinori NAKAMURA, Hiroyuki DOI and Toyoaki MIYAGAWA

543

Lecture (Vol.50 No.5)

Application of Reliability Engineering for Safety Design and Maintenance against Mechanical Structure and Components ‡X:Ceramic Materials and Components for Energy Systems in Automobiles

Hiroshi KAWAMOTO

550